High quality kite with uno R3, 100 percent compatible with Arduino uno R3
Elegoo Inc. is a professional manufacturer and exporter that is concerned with the design, development production and marketing of arduino, 3d printers, raspberry pi and STM32. Our Dream is to make the best price and best quality produce for customers. So we would like to receive your valuable suggestions for our products and we can improve them for you.
Component listing: 1pcs UNO R3 Controller Board 1pcs LCD1602 Module ( with pin header) 1pcs Breadboard Expansion Board 1pcs Power Supply Module WARNING: Pls. do not use the voltage higher than 9V 1pcs Joystick Module 1pcs IR Receiver 1pcs Servo Motor (SG90) 1pcs Stepper Motor 1pcs ULN2003 Stepper Motor Driver Board 1pcs Ultrasonic Sensor 1pcs DHT11 Temperature and Humidity Module 1pcs 9V Battery with DC 1pcs 65 Jumper Wire 1pcs USB Cable 1pcs Active Buzzer 1pcs Passive Buzzer 1pcs Potentiometer 1pcs 5V Relay 1pcs Breadboard 1pcs Remote 1pcs Tilt Switch 5pcs Button (small) 1pcs 1 digit 7-segment Display 1pcs 4 digit 7-segment Display 5pcs Yellow LED 5pcs Blue LED 5pcs Green LED 5pcs Red LED 1pcs RGB LED 2pcs Photoresistor 1pcs Thermistor 2pcs Diode Rectifier (1N4007) 2pcs NPN Transistor (PN2222) 1pcs IC 74HC595 120pcs Resistor 10pcs Female-to-male Dupont Wire
When I ordered this, I figured it would be some cheap little (you get what you pay for) kit. I figured it would at least be good enough to dip my hand into the Arduino world. Then when it arrived, I quickly realized this isn’t some little makeshift kit. This project kit comes with everything you could need to get you started with learning arduino. Everything in the kit was of good/excellent quality. There are a lot of tutorials online to tinker with all the sensors, motors, lcds, etc in this kit. I’ve learned so much in the few days that I have had this. I decided to learn Arduino so I could build a low voltage cutoff switch into my solar equipment. After just a few days of learning Arduino hardware and software, I feel like I have 90% of the knowledge I need for my first project. Wish me luck!
The resistors are hard to read: they have the bands oddly grouped up, so you can’t tell which way to orient to read them. The tutorial PDF is okay, but could use better formatting, like links to jump to each chapter.
Fantastic introduction to this powerful and small electronic control unit. Fun projects that help you learn about electronics, robotics, and control systems.
Great set for prototyping and learning. Got one to play with Arduino and so far it’s an absolute blast.
i love this kit havent used alot of the stuff instead but the stuff i have used worked really well.
Great bang-for-your-buck purchase, comes with everything you need to get started and more. Definitely recommend this kit.
Great product for the price! I still cannot believe I got this much for the price! Rant helpful for starters and for those who are following tutorials and books. You got almost everything to learn for. I wood highly recommend it.
Great kit with good tutorial. Great for beginners with the whole package
Fantastic bang for the buck, but the large breadboard was too sloppy to use for any prototyping.
Great product. I did have a couple wires that were faulty, just be sure to always test your connections with a multimeter so you don’t go crazy while working on a project ;) thank…
This is a great starter/novice setup. I went into this already knowing something I wanted to build so after following a handful of examples, I branched off and built my device.
great product. As listed.
unit does not work want my money back
great value
This is an outstanding value. I’ve been playing with mcu’s for years, starting with Basic Stamps, then roll-your-own AVR chips, the RasPi, Circuit Playground, etc.
shipping and product met expectations.
Very complete kit for learning microprocessor programming and application.
comments powered by DisqusGood gift for electronics hobbiest.