VideoSecu LCD/DLP Projector Ceiling Mount Bracket White Fits both flat or Vaulted ceiling PJ2W 1CA
by people ...
Product Specifications
- Mounting arms removable and extendable, 3” extra extension adaptor included
- Without extension pole, the height is 5.9”; With extension pole, height adjust from 18.1” to 26.7” (45.9-67.8 cm); Ceiling plate adjustable 0 to 90 degree swivel
- Heavy duty steel construction, Maximum loading 44 lbs (20 kgs); Rotate adjustment left and right 5 degrees
- Integrated cable management; Exclusive “No-slip” adjustment system; Lock in any position; Easily release and lock
Standard size hardware,comprehensive installation manual included.VideoSecu brand. Please report to Amazon.com if you recieve a mount without VideoSecu logo
Product Description
Style:PJ2W This mount is VideoSecu brand. Mount features a flexible mounting system that can be used with most projector model, and it has the versatility to attach to nearly any ceiling. The mounting interface features four double-jointed support arms that allow flexible positioning to reach almost any mounting point of the projector. Each arm can be precisely positioned to avoid covering important projector ventilation and access points used for lamp and air filter replacement. This minimizes heat build-up and maximizes lamp life. Its robust construction allows the mount to positively hold the projector fixed at nearly any angle. This mount’s tilt and roll can be adjusted independently of one another, compared to the clumsier adjustments needed for ball-and-socket mounts. it comes with an adjustable channel and ceiling plate. This allows the projector to be mounted at an adjustable height from the ceiling. This auction is for 1 set of White projector ceiling mount. Does this mount fit my projector? Please look at the mounting screws on the top of your projector. Measure the distance between the holes. If your projector has 3 holes pattern or 4 hole pattern, and the maxim distance between any two holes(especially diagonally) is less than 12.5 inch/32 cm, then this mount will fit your projector. If your projector has holes more than 12.5” apart, you need 5” extender (sold separately in our Amazon store ASIN: B0036849J6) which can cover an area up to 17 inch in diameter
Product Reviews
This worked fine for Epson PowerLite Home Cinema 2030
Able to set it up in about 2 hours with most of my time organizing and troubleshooting. I think the parts are plenty good in quality. The instructions are not the greatest. If you take your time and think about what you are doing and what the instructions suggest, it will go up fine. Lay out all the parts as shown in the instructions which makes it easier to install what you need. Be sure to use the washer spacers to attatch to the ceiling bracket. The attatched photo should help. Plenty of adjustments to aim the projector once done as can only get close to the center of gravity given the attachment points for the 2030. I love it.
Five Stars
I was a little doubtful of getting this bracket because noone on the other reviews or questions answered the question with a definite answer. A lot of people we’re asking if this works with the Epson 2030, everyone’s answer was “it should, it’s a universal bracket and it should work.” That is not the answer I wanted to see. The definite answer to question is “YES”, it fits the Epson 2030. As you can see in the picture, only 3 arms will attach to the projector. That’s a fault on the projector, not the bracket, but it still works though.
Would work well for an older model, but required two DIY modifications to fit my Optoma HD27
This got the job done but for my specific projector, there were some issues. I bought this for an Optoma HD27, for which there are only three mounting holes on the projector and they’re all located very close together. This projector mount has four arms and instructions for how to remove one arm and move another to a “center” hole. My mount only had four holes and no center hole, so it was different than the instructions and therefore I had to angle it to fit my three-hole projector.The second issue was with the Optoma HD27, all three holes on the projector were very close together. I could see this mount working well for projectors with holes on each corner, but the Optoma had holes about 3in apart. The extender arms on the mount were too big to fit the holes, so I had to cut through the metal to create smaller arms that would fit the projector holes and still lock into the mount.Overall, this would likely work well for an older model projector, but it would not fit the HD27 out of the box and required two modifications.
If you want a seriously competent mount look elsewhere. You get what you pay for.
I ultimately returned this product. It’s capable but not ideal. It’s low quality it very apparent and if you want precision adjustment look elsewhere. I ended up buying the PEERLESS AV PRG3 in white: https://www.amazon.com/PEERLESS-AV-PRG3-EXC-W-Universal-Projector-Extension/dp/B0156IQJX2/ref=sr_1_1?ie=UTF8&qid=1471639251&sr=8-1&keywords=PRG3-EXC-WIt is substantially far more competent mount check the images for reference. I can’t even begin to explain how much easier the PEERLESS is to setup, adjust and fine tune. Plus once its lock in place no amount of vibration (kids running around upstairs, wind, etc…) is going to budge it.My projector is mounted on a screened in porch and nothing budges it using the PEERLESS. This one was vibrating in the wind and just felt flimsy.
infinite flexibility if you have infinite time. For optoma hd28dse I suggest the other recommended mount
This is not a complete solution (does not include screws for attaching to projector itself) and takes a lot of time and effort to setup. The instructions are bad. The product itself is pretty ugly, the only consideration was function. If you have large ceiling drop it is probably a good solution. And if you don’t mind fiddling with it to get it to work. For me, I should have just purchased the more expensive mount but I saw that people said this worked well with the Optoma HD28DSE and this was $35 cheaper…it may work but you have to spend a lot of time configuring the arms to match the mounting posts on the projector, and then take a trip to the HW store to get the M5 screws to attach it. And there might have been other issues but I stopped trying after realizing that it would take all of this time and that for a few more $ I could get the better / faster solution.
Not quite universal…
This universal projector mount is sadly not quite universal (Unless you ghetto rig it. See bott. It does not have a large enough mounting plate (mounting arms) to fit my projector, an Epson 8700 UB. I did not figure this out until AFTER I put the damn thing together, so do yourself a favor and make sure you try the mounting plate on your projector before you go through the hassle. If you don’t, and you follow the order of the instruction manual, you may end up in my position. :(I will say, that after I put the thing together, it was extremely sturdy. I mean, you could kill zombies with it. That said, I did make a minor tweak to its design. On the bottom side of the outer part of the extension piece, I slid a washer between where the inner and outer sections touched on the side with the back plate. It gives you way more washers than you need, and I did this to make one of the three screws stretching the inside portion of the extension more effective at keeping the device sturdy while not poking through the back of the inside back plate. I know that sounds confusing, but if you’re looking at the product and trying to put it together, it won’t be.Also, the parts that were included did not coincide with what was in the manual in terms of quantity, but that’s because the manual has incorrect numbers. All of the parts necessary to install this thing are there. It’s really easy to do too.Anyway, I would recommend this if you don’t have a gigantic projector. Being that this projector is my first, I didn’t really think it was that large. I guess I was wrong.*I DID NOT RETURN THE PRODUCT. I DECIDED TO GHETTO RIG IT BECAUSE IT’S ONE OF THE CHEAPEST MOUNTS ON AMAZON. Because I’ve seen people hang the Epson 8350 with only 3 screws, I knew this one could be done like that as well. That said, I looked at what pieces it came with, and I decided on doing a 4 hole mount. I was able to achieve this by adding a few additional screws and bolts of my own to connect two of the long legs each to a short leg and then screwing in to the mounting hole on the projector. I’m admittedly not using one of the ideal holes on the projector because a screw broke while trying to reverse it. After trying for way too long with a stripped screw removal tool, I finally gave up on that hole.*see pictures of the product for pics uploaded by me for how to make this work
Bad instructions, bad product…
Terrible instructions! This was very difficult to piece together and when we finished putting it all together the fit to the projector had to be tinkered to for just right.
Good, solid, but tricky…
Pretty tough to get it all together to hold my Optoma GT1080, but was able to sort it out. Instructions weren’t great, but again… I got the job done.
> > > This is Likely the Best Projector Mount One Can Get
I hope you find this review helpful. - My Epson 1040 was set to project from the ceiling and this mount was by far the best bang for the buck.
Five Stars
Love It.
works as a door stop
did not fit any of my 3 projectors, I am using it as a door stop
Working great. We had a three hole mount on our …
Working great. We had a three hole mount on our projector so it took some time to get the arms to adjust to the proper mounting position, but once that was done everything went…
Great product
Item worked as advertised. I’m very pleased with this product.
OK product, serves the purpose, cud have been a little more sturdy
I would have bought PJ1W model (https://www.amazon.com/dp/B01DNJHYQ2/ref=cm_cr_ryp_prd_ttl_sol_31?th=1) and saved some money.
Five Stars
Works as advertised
Five Stars
comments powered by DisqusFits my projector
